NTP on Cisco WAPs

24 07 2014

Found that I was unable to configure NTP on my Cisco Aironet 1250’s in the same way I had on my switches as per here

I was, however, able to configure the timezone and BST settings.

I thought it strange that I could set that but not an NTP server.

A quick bit of digging uncovered the fact that the WAPs need ‘SNTP’ (Simple Network Time Protocol) servers to be configured, instead of ‘NTP’ servers. The difference being that a device configured to use SNTP can only be a client, not a server.

So the configuration becomes:

#sntp server x.x.x.x

The timezone and BST settings are identical.

Advertisements




NTP on Cisco switches / routers

23 07 2014

Have been looking recently to review processes and introduce efficiencies where possible. One of the monthly tasks that I set myself was to ensure the time hadn’t slipped too far on my Cisco devices, and to correct it if it had.

A power cut in one of the offices caused all my Cisco devices to reset their time to the default of Mar 1993.

These two factors combined triggered some research into implementing NTP on all Cisco devices.

Commands I used on all devices are as follows. Devices were a combination of Catalyst 3560 and 3750 switches. Routers were already configured accordingly.

#clock timezone GMT 0
#clock summer-time BST recurring 4 SUNDAY MARCH 01:00 4 SUNDAY OCTOBER 02:00 60
#ntp server x.x.x.x
#ntp server x.x.x.x

This sets the timezone to GMT, specifies BST (British Summer Time) as the daylight savings timezone, set it to recur, starting from the 4th Sunday of March to the 4th Sunday of October, and specifies the NTP servers to use. I’ve found that Server 2008 R2 Domain Controllers work pretty well as a reference NTP server for a number of different device types including Linux based (Check Point firewalls / Coyote Point load balancers) as well as Cisco devices.. my environment doesn’t require nanosecond accuracy, but we do need to be able to correlate times in logs with specific events, which Server 2008R2 provides.

For troubleshooting / verification, I used these commands:

#show clock detail

The output of this is:

11:33:32.081 BST Wed Jul 23 2014
Time source is NTP
Summer time starts 01:00:00 GMT Sun Mar 23 2014
Summer time ends 02:00:00 BST Sun Oct 26 2014

It shows the time, time source, and start / end of the summer time – useful stuff. Time source is ‘user configured’ if NTP has not been used.

#show ntp associations

This shows the IP addresses of the NTP servers configured, what their reference clock sources are, and their ‘stratum’ (the output is largely IP address related, hence leaving it out here).

#show ntp status

Clock is synchronized, stratum 4, reference is x.x.x.x
nominal freq is 119.2092 Hz, actual freq is 119.2076 Hz, precision is 2**18
reference time is D77A0BC8.3817A4F2 (11:24:08.219 BST Wed Jul 23 2014)
clock offset is -18.8268 msec, root delay is 120.00 msec
root dispersion is 159.91 msec, peer dispersion is 28.58 msec

The shows a bunch of info – the most important part is ‘Clock is synchronised’.

Info provided without warranty, please test before implementing. I don’t have the luxury of a test environment myself, but due to the low-potential for negative impact in this case, implemented the above on a switch with minimal ports in use before implementing network-wide.





Passed CCNP SWITCH!

16 07 2014

Passed the SWITCH quite comfortably on the third attempt on Monday 14th July. Now on to the ROUTE!

My CCNA is already reflecting the new expiry date on the Certification portal – this was previously due to expire in October.

I’ve purchased the Chris Bryant CCNP ROUTE e-book, as I found his SWITCH book incredibly good, and it’s about a quarter of the price of the other books on the market, and more importantly, a much, much easier read, being written in a very casual tone rather than the somewhat stuffy, formal styles associated with Cisco Press etc. I also bought his CCNP SWITCH video series on Udemy, so may well go for the ROUTE equivalent. I already have the CBTNuggets video series for the ROUTE, so I have enough to keep me going.

Aiming to get it passed by the end of the year, although it took 2.5 years to get there with the SWITCH! The fact that all three CCNP exams have to be passed within three years of each other makes this slightly more urgent though.





CCNP SWITCH Take 3!

29 04 2014

Failed the SWITCH exam again in March, this time having had a couple of days study leave. My score was *much* closer to the pass mark this time though, which was some consolation.

Booked again for the next month or so!





CCNP SWITCH Re-booked..

17 03 2014

.. for the 31/3. Gulp.





Wisdom from a potential supplier

21 02 2014

So I get a call, in which the salesman is trying to get me to start using his company, and one of his questions is ‘did you know Windows XP is going out of support soon?’.

My response? ‘Anyone in IT who doesn’t know that doesn’t deserve to work in IT’.

Made me chuckle.

It’s since taken two days and counting to get a quote on a bunch of monitors! Guess I’ll be swerving these guys then.





CCNP Exam

21 02 2014

Ended up taking and failing the SWITCH in November.

I wasn’t too disappointed with the score; although I’d swatted up on, and gained experience with, the core technologies tested, I fell down due to a lot of questions on what I’d consider pretty niche features.

My current revision is focused on learning these features. I reckon the retake will end up being some time in March.